Installation & Operating Instruction Manual® TRANSPORTER
101. Verify that the Extension, Inner Disc, and Valve Rod must be very straight and not overtightened.2. Assemble all components of the Piston Valve A
11 Use Six M6 Screws8mm Deep Thread for Tray MountingSpeedAdjustmentScrew4.9”125mm1.8”45mm.78”20mm4.52”115mm1.8”45mm2.4”60mm2.6”67mm1.2”30mm8.5”216mm2
12Part No. Description Qty*T10-106 Guide column sleeve 4T10-201 Rear holder 1T10-202 Front holder 1T10-203 Threaded guide column 2T10-204 Tray hold
13T10-214T10-202*T10-213T10-212T10-414T10-413T10-605T10-203T10-106*T10-319T10-303*T10-212T10-201T10-209T10-210T10-204T10-305*T10-316T10-325*T10-602T10
14Reassemble in reverse order, using caution not to bendthe Valve Disc Assembly.1. Remove the Air Regulator Rod T40-029 by loosening the set screw in
15Use Six M8 Screws9mm Deep Threadfor Tray Mounting 6.3” 160mm3.5” 89mm1/4” NPTUse Two M10 Boltsfor Mounting9.8”250mm.4”10mm2.7”68mm1.3”32mm3.6”92mm5.
16Part No. Description QtyT3-407 Regulator O-ring (14208-008) 1T10-210 Flat head screw (6mm) 10T10-605 Speed adjustment screw 1T40-001 Foot 1T40-006
17*Included in Repair Kit 40-101 (17271)TP-40 PARTS DRAWINGT40-029T40-006T40-058*T40-608T3-407T40-065T40-069*T40-046T40-602T40-055T40-071T40-604T40-05
18When reassembling, take care with the following:1. Install Speed Adjustment Valve and align indent for the Speed Adjustment Valve Locking Screw.2. R
19Use Six M8 Screws8mm Deep Threadfor Tray MountingUse Six M8 Boltsfor MountingSpeedAdjustmentKnob3.0”77mm3.9”99mm1.8”46mm12.8”325mm1.6”41mm2.5”64mmTy
P/A INDUSTRIES INC.APPLICATIONS ... 3INSTALLATION ...
20Part No. Description QtyT3-407 Cylinder rod O-ring (14208-008) 2*T10-319 Speed adjustment knob O-ring 1*T10-320 Plug O-ring 1*T40-010 Valve seals 2
21T70-216T70-434T70-410T70-220T70-602T70-411T70-404*T70-215*T40-047T70-153T70-154T70-257T40-010T70-605T70-105*T40-010T70-259T70-217*T70-215T70-601T70-
22When reassembling, take care with the following:1. Install the Speed Adjustment Valve T140-308 andtighten Sleeve T140-326 using an 8 mm Hexagon Wren
23Use Six M8 Screws8mm Deep Threadfor Tray MountingUse Six M8 Boltsfor MountingSpeedAdjustmentKnob3.0”77mm5.8”148mm12.8”325mm2.5”63.5mmTyp.7”179mm4.8”
24Part No. Description QtyT3-407 Cylinder rod O-Ring (14208-008) 2*T10-319 Speed adjustment knob O-Ring 1*T10-320 Plug O-ring 2*T40-010 Valve seals 2
25T140-402T140-410*T70-220T70-602T140-404T70-411*T70-215T40-047T70-153T70-154*T70-257T40-010*T70-603*T3-407 (*14208-008)T70-605*T40-010T70-259T70-217T
26TECHNICAL DATAMax.Length Rate incline Trans- Max.Air Air of of of Feed Sound portation weightModel Pressure Consumption Stroke Feed Chute Level Weig
27Roller Slide Tray Support OptionsRoller Slide DimensionsSEALMounting PlateBall BearingsSlide RailGuide PlateStopperBall BearingsSlide RailModel RS-1
Toll-Free: 1-800-243-8306, Worldwide: 1-860-243-8306, Fax: 1-860-242-4870, E-mail: [email protected] FORM 1053 11-07P/A INDUSTRIES INC., 522 Cottage Gro
3U.S. PATENT NO.4,444,346Design the trayconfigurationto suit your applicationThird Stage BlankModel TP-10Second Stage PunchFirst StagePierceProgressiv
4INSTALLATION4. Connect the Air Line with flexible poly-flow tubing intothe threaded inlet. On Model TP-3 use 1/4” tubing for1/8” NPT. Models TP-10,
57. The Conveyor tray or chute must be supported atboth ends to minimize vibration and deflection. A block ofDelrin GP-500 or Nylon, low friction mat
61. Remove both Snap Rings and push the Front and Rear Pistons inside Body.2. Remove the Screws from the Rear Guide Holder T3-204. Pull out together w
75.5”140mm1/8” NPT7”178mmUse Six M6 Screws8mm Deep Threadfor Tray MountingUse FourM8 Bolts forMounting 3.3”83mm1.3”34mm4.7”120mm.75”19mmSpeed Adjustme
8Part No. Description QtyT3-105 Screw 8T3-107 Air inlet 1T3-110 Mounting plate 1T3-111 Mounting plate screw 4T3-112 Spring pin 4T3-201 Guide holder (
9TP-3 PARTS DRAWINGT3-105T3-203*T3-327T3-110T3-111T3-323*T3-602T3-601T3-325*T3-311*T3-602*T3-307T3-308*T3-322T3-303T3-201*T3-327T3-107T10-209T3-302T3-
Commentaires sur ces manuels